my Toyota Corolla E170 (2013-2019) has a check engine light and no power, what should I do?

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

559 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix check engine light and power loss issues in Toyota Corolla E170 (2013-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before inspecting components.

Symptoms

•Check engine light illuminated
•Noticeable loss of power during acceleration
•Engine rough idling
•Unusual engine noises (e.g., knocking or pinging)
•Decreased fuel efficiency
•Potential stalling or hesitation when driving

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify specific trouble codes.
2
Check the engine oil level and condition, ensuring it is within the recommended range and not contaminated.
3
Inspect the air filter for clogging or excessive dirt and replace if necessary.
4
Examine the throttle body for carbon buildup or obstruction.
5
Test the fuel pressure using a fuel pressure gauge to ensure adequate fuel delivery.
6
Inspect the ignition system components, including spark plugs and ignition coils, for wear and functionality.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Fuel pressure gauge
•Multimeter
•Throttle body cleaner
•Soft cloth

Parts Required

•Fuel filter (if needed)
•Spark plugs (if needed)
•Throttle body cleaning supplies

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify specific trouble codes.
2
Check the engine oil level and condition, ensuring it is within the recommended range and not contaminated.
3
Inspect the air filter for clogging or excessive dirt and replace if necessary.
4
Examine the throttle body for carbon buildup or obstruction.
5
Test the fuel pressure using a fuel pressure gauge to ensure adequate fuel delivery.
6
Inspect the ignition system components, including spark plugs and ignition coils, for wear and functionality.

Solution

1. Preparation

Gather tools: OBD-II scanner, socket set, fuel pressure gauge, multimeter, cleaning supplies.
Ensure the vehicle is parked on a flat surface and the engine is turned off before starting repairs.

2. Address Error Codes

Plug in the OBD-II scanner and retrieve error codes.
Document all codes for reference.
Clear codes and perform a test drive to see if they reappear, indicating persistent issues.

3. Inspect and Clean Throttle Body

Remove the intake duct connected to the throttle body using the socket set.
Use throttle body cleaner and a soft cloth to clean the throttle plate and housing.
Reassemble the intake duct and ensure all connections are secure.

4. Test and Replace Fuel Filter (if necessary)

Locate the fuel filter and relieve fuel pressure by removing the fuel pump fuse and running the engine until it stalls.
Disconnect fuel lines from the filter using the appropriate tool.
Replace the old filter with a new one, ensuring proper orientation and secure connections.

5. Check and Replace Spark Plugs

Remove the ignition coil cover (if applicable) using a socket set.
Carefully unclip and remove ignition coils, and then extract the spark plugs using a spark plug socket.
Inspect spark plugs for wear and replace with new ones if necessary, ensuring the gap is set according to manufacturer specifications (typically 0.043 inches).