my Toyota Corolla E170 (2013-2019) has a loud knocking noise, what does it mean?

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

509 words

Problem Statement

Diagnose and fix loud knocking noise in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening the hood or performing any inspections.

Symptoms

•Loud knocking noise from the engine or suspension
•Possible loss of power during acceleration
•Increased engine vibrations
•Check engine light illuminated (if applicable)
•Unusual wear on tires (if related to suspension)

Diagnostic Steps

1
Inspect the engine bay for loose or damaged components.
2
Use an OBD-II scanner to check for any stored error codes.
3
Check the oil level and condition; low or dirty oil can cause knocking.
4
Perform a visual inspection of the suspension components for wear or damage.
5
Start the engine and listen for the noise while moving to pinpoint its source.
6
Test drive the vehicle to observe any changes in performance or noise characteristics.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Wrench set
•Jack and jack stands
•OBD-II scanner
•Stethoscope (or similar sound-detecting tool)

Parts Required

•Engine oil (SAE 0W-20)
•Oil filter
•Any necessary suspension components (struts, bushings, etc.)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the engine bay for loose or damaged components.
2
Use an OBD-II scanner to check for any stored error codes.
3
Check the oil level and condition; low or dirty oil can cause knocking.
4
Perform a visual inspection of the suspension components for wear or damage.
5
Start the engine and listen for the noise while moving to pinpoint its source.
6
Test drive the vehicle to observe any changes in performance or noise characteristics.

Solution

1. Preparation

Tools Required: Socket set, wrench set, jack and jack stands, OBD-II scanner, stethoscope (or similar sound-detecting tool).
Ensure the vehicle is parked on a level surface and the ignition is off.
Disconnect the battery to prevent any electrical issues during the inspection.

2. Inspect and Tighten Engine Components

Sub-steps:
- Visually check all engine mounts for wear or damage.
- Tighten bolts on the engine components, including the intake and exhaust manifolds.
- Check and replace any loose or damaged heat shields.

3. Oil Check and Change

Sub-steps:
- Remove the oil dipstick and check the oil level. If low, add the recommended oil type (typically SAE 0W-20 for Corolla).
- If the oil is dirty or old, drain the oil using a socket set, replace the oil filter, and refill with fresh oil.
- Ensure the oil is at the correct level after refilling.

4. Suspension Inspection and Repair

Sub-steps:
- Raise the vehicle using a jack and secure it with jack stands.
- Inspect struts, shocks, and bushings for wear or damage.
- Replace any worn suspension components with OEM parts.
- Reassemble and lower the vehicle.

5. Reconnect Battery and Test

Reconnect the battery terminals.
Start the vehicle and listen for any remaining knocking noise.
If the noise persists, further internal engine inspection may be necessary.