FAULTBASE
Error CodesASKCars
© 2026 FAULTBASE
All rights reserved.
v2.0.0 • Production
ContactPrivacyImpressum
my Toyota Corolla E170 (2013-2019) has a rough start in cold weather - Toyota Corolla
Home/Cars/Toyota/Corolla/E170 (2013-2019)/my Toyota Corolla E170 (2013-2019) has a rough start in cold weather

my Toyota Corolla E170 (2013-2019) has a rough start in cold weather

Toyota Corolla E170 (2013-2019)

Error Codes
2-4 hours
Time
medium
Difficulty
medium
Severity
Navigation
ProblemSymptomsDiagnosisSolution
ProblemSymptomsDiagnosisSolution
3 min read
549 words

Problem Statement

Learn how to diagnose and fix rough starting issues in cold weather for the 2013-2019 Toyota Corolla E170. Step-by-step guide with diagnostic procedures.

Affected Component
Electrical
Estimated Time
2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

  • •Disconnect the battery before working on electrical systems
  • •Allow the engine to cool before working on the fuel system and spark plugs

Symptoms

  • •Engine cranks but struggles to start
  • •Rough idle immediately after starting
  • •Increased engine vibration
  • •Possible engine stalling shortly after starting
  • •Check engine light may illuminate intermittently

Diagnostic Steps

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. 6

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

  • ✓Test the affected component to ensure it functions correctly
  • ✓Check for any error codes or warning lights
  • ✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

  • •Follow the manufacturer's recommended maintenance schedule
  • •Address warning signs early before they develop into major issues
  • •Use quality parts and fluids recommended for your vehicle
  • •Keep detailed records of all repairs and maintenance

Tools & Equipment Required

  • •OBD-II scanner
  • •Multimeter
  • •Socket set
  • •Torque wrench

Parts Required

  • •New battery (if applicable)
  • •Fuel filter
  • •Spark plugs
  • •Engine coolant temperature sensor (if applicable)
  • •Fuel injector (if applicable)

Additional Information

Affected Component
Electrical
Estimated Time
2-4 hours
Difficulty
medium
Severity
medium
Tools Required
4 items
Parts Required
5 items

Related Faults

Loading...

Share this solution

Comments

Sign in to share your thoughts

Sign In

No comments yet

Be the first to share your thoughts

Back to Generation
Solution
1. Preparation
  • Gather tools and parts needed for the repair.
  • Disconnect the battery to ensure safety during diagnostics.

Tools Required:

  • OBD-II scanner
  • Multimeter
  • Socket set
  • Torque wrench
2. Battery Inspection and Replacement
  • Check the battery voltage using a multimeter.
  • If the voltage is below 12.4 volts, replace the battery.
  • To replace:
    1. Remove the negative terminal first, followed by the positive terminal.
    2. Remove the battery hold-down bracket and lift out the old battery.
    3. Place the new battery in the tray and secure it with the hold-down bracket.
    4. Connect the positive terminal first, then the negative terminal.
3. Fuel System Inspection
  • If fuel pressure is low:
    1. Replace the fuel filter if it hasn’t been changed in the last 30,000 miles.
    2. Inspect and replace the fuel pump if necessary.
4. Spark Plug Inspection and Replacement
  • Remove the spark plugs using a socket set.
  • Inspect for wear or fouling; if necessary, replace with OEM specifications.
  • Torque the new spark plugs to the manufacturer’s recommended settings (typically around 13-15 ft-lbs).
5. Engine Coolant Temperature Sensor Inspection
  • Locate the engine coolant temperature sensor.
  • Disconnect the electrical connector and check the resistance with a multimeter.
  • Replace the sensor if it is outside the specified resistance range for cold temperatures.
6. Fuel Injector Testing
  • Use a multimeter to check the resistance of each fuel injector.
  • Clean or replace any injectors that do not meet specifications.