my Toyota Corolla E170 (2013-2019) is consuming too much oil what could be the cause

Toyota Corolla E170 (2013-2019)

Error Codes

4-8 hours

Time

hard

Difficulty

high

Severity

3 min read

467 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix excessive oil consumption in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Engine

Estimated Time

4-8 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow engine to cool before opening any components.

Symptoms

•Check engine light illuminated
•Blue smoke from the exhaust
•Increased oil consumption between oil changes
•Engine knocking or ticking noises
•Oil spots or leaks under the vehicle
•Poor engine performance or rough idling

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to check for any related fault codes.
2
Inspect the engine oil level and condition using the dipstick.
3
Check for external oil leaks by inspecting the oil pan, valve cover gasket, and seals.
4
Perform a compression test on the engine cylinders to assess their condition.
5
Conduct a leak-down test to check for issues with the piston rings or valve seals.
6
Inspect the PCV (Positive Crankcase Ventilation) system for blockages or malfunctions.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Compression tester
•Leak-down tester
•Screwdrivers

Parts Required

•Engine oil (manufacturer-recommended grade)
•New piston rings (if applicable)
•PCV valve (if applicable)
•Gaskets and seals (as needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to check for any related fault codes.
2
Inspect the engine oil level and condition using the dipstick.
3
Check for external oil leaks by inspecting the oil pan, valve cover gasket, and seals.
4
Perform a compression test on the engine cylinders to assess their condition.
5
Conduct a leak-down test to check for issues with the piston rings or valve seals.
6
Inspect the PCV (Positive Crankcase Ventilation) system for blockages or malfunctions.

Solution

1. Preparation

Gather tools and parts needed for the repair.
Ensure the vehicle is on a level surface and the engine is cool.
Disconnect the negative battery terminal to prevent electrical issues.

2. Addressing External Leaks

Sub-steps:
1. Clean the area around potential leak sites with a degreaser.
2. Replace any damaged gaskets or seals found during inspection.
3. Refill the engine oil to the correct level after repairs.

3. Replacing Piston Rings (if necessary)

Sub-steps:
1. Remove the engine from the vehicle following the manufacturer's specifications.
2. Disassemble the engine to access the pistons.
3. Remove old piston rings and install new ones, ensuring proper orientation and clearance.
4. Reassemble the engine, ensuring all torque specifications are met.

4. PCV System Repair

Sub-steps:
1. Inspect the PCV valve for blockage or damage.
2. Replace the PCV valve if it is not functioning correctly.
3. Clean or replace any clogged hoses in the PCV system.