my Toyota Corolla E170 (2013-2019) won't start in the morning what could be wrong

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

527 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix the no-start issue in your 2013-2019 Toyota Corolla E170. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Electrical

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool completely before inspecting components.

Symptoms

•Engine cranks but does not start
•Engine does not crank at all
•Clicking sound when the ignition is turned
•Weak or dim dashboard lights
•Battery warning light illuminated
•Fuel gauge shows low fuel level even with a full tank

Diagnostic Steps

1
Check the battery voltage with a multimeter; it should be above 12.4 volts.
2
Inspect battery terminals and cables for corrosion or loose connections.
3
Test the starter motor by attempting to jump-start the vehicle.
4
Scan for error codes using an OBD-II scanner to check for any stored trouble codes.
5
Verify fuel pump operation by listening for the pump sound when the ignition is turned on.
6
Check fuses related to the ignition system and fuel pump for any blown fuses.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Multimeter
•Socket set
•Wire brush
•OBD-II scanner

Parts Required

•New battery (if necessary)
•Starter motor (if necessary)
•Fuel filter (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the battery voltage with a multimeter; it should be above 12.4 volts.
2
Inspect battery terminals and cables for corrosion or loose connections.
3
Test the starter motor by attempting to jump-start the vehicle.
4
Scan for error codes using an OBD-II scanner to check for any stored trouble codes.
5
Verify fuel pump operation by listening for the pump sound when the ignition is turned on.
6
Check fuses related to the ignition system and fuel pump for any blown fuses.

Solution

1. Preparation

Gather all necessary tools and parts.
Ensure the vehicle is in a safe location with adequate ventilation.
Disconnect the negative battery terminal to prevent any electrical shorts.

2. Battery Inspection and Replacement

Inspect the Battery:
- Remove the battery terminals (negative first, then positive).
- Clean any corrosion from terminals and cables using a wire brush.
Test Battery:
- Use a multimeter to check the battery voltage. Replace if below 12.4 volts.
Replace Battery (if needed):
- Remove the old battery and install a new one, ensuring correct orientation.
- Reconnect the positive terminal first, then the negative terminal.

3. Starter Motor Check

Test Starter:
- Locate the starter motor and check connections for tightness and corrosion.
- Using a multimeter, test for voltage at the starter solenoid while someone turns the ignition key.
Replace Starter (if necessary):
- Remove the electrical connections and mounting bolts from the starter.
- Install the new starter and reconnect the electrical connections.

4. Fuel System Check

Inspect Fuel Pump:
- Locate the fuel pump relay and check for proper operation or replace if faulty.
- Check the fuel lines for any leaks or blockages.
Replace Fuel Filter (if needed):
- Disconnect the fuel lines from the filter, following proper safety procedures to relieve fuel pressure.
- Replace the fuel filter and reconnect the lines.