why does my Toyota Corolla E170 (2013-2019) check engine light keep coming on

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

541 words

Problem Statement

Learn how to diagnose and fix the persistent check engine light issue in your 2013-2019 Toyota Corolla E170. Step-by-step guide included.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems
•Allow the engine to cool before working on it to avoid burns

Symptoms

•Check engine light illuminated
•Rough idle
•Decreased fuel efficiency
•Engine stalling
•Poor acceleration
•Increased emissions

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner
2
Check the gas cap for proper sealing and signs of damage
3
Inspect the air filter for blockages or excessive dirt
4
Examine spark plugs and ignition coils for wear or damage
5
Test the battery and charging system voltage
6
Check for vacuum leaks in hoses and intake manifold

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Multimeter
•Vacuum gauge
•Torque wrench

Parts Required

•Replacement gas cap (if faulty)
•New air filter
•New spark plugs (if worn)
•New ignition coils (if damaged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner
2
Check the gas cap for proper sealing and signs of damage
3
Inspect the air filter for blockages or excessive dirt
4
Examine spark plugs and ignition coils for wear or damage
5
Test the battery and charging system voltage
6
Check for vacuum leaks in hoses and intake manifold

Solution

1. Preparation

Gather tools and parts. Ensure the vehicle is parked on a level surface.
Tools Required: OBD-II scanner, socket set, multimeter, vacuum gauge, torque wrench.
Safety Warnings: Disconnect the battery before working on electrical systems.

2. Retrieve Error Codes

Use the OBD-II scanner to connect to the vehicle's diagnostic port.
Record any error codes displayed, as this will guide subsequent repairs.

3. Inspect and Replace Faulty Components

Gas Cap:
- Remove the gas cap and inspect the rubber seal for cracks.
- If damaged, replace it with a new cap.
Air Filter:
- Remove the air filter housing cover.
- Inspect the air filter; if dirty or clogged, replace it with a new one.
Spark Plugs and Ignition Coils:
- Remove the ignition coils using a socket set.
- Inspect spark plugs for wear; replace if necessary (usually every 30,000-60,000 miles).
- Reinstall new or cleaned spark plugs and ignition coils.

4. Check for Vacuum Leaks

Use a vacuum gauge to check for leaks in hoses.
Inspect the intake manifold gasket for any signs of wear or damage.
Replace any damaged hoses or gaskets.

5. Test Battery and Charging System

Use a multimeter to check the battery voltage; it should read around 12.6 volts when fully charged.
Start the engine and check the voltage again; it should be between 13.7 to 14.7 volts.
If readings are outside these ranges, consider replacing the battery or alternator.