why does my Toyota Corolla E170 (2013-2019) engine light keep coming on

Toyota Corolla E170 (2013-2019)

Error Codes

1-3 hours

Time

medium

Difficulty

medium

Severity

3 min read

520 words

Problem Statement

Learn how to diagnose and fix the engine light issue in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Engine

Estimated Time

1-3 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components
•Allow the engine to cool before inspecting or replacing parts

Symptoms

•Check engine light illuminated
•Rough idle or engine hesitation
•Decreased fuel economy
•Engine stalling or misfiring
•Poor acceleration or power loss
•Unusual engine noises (knocking or pinging)

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to retrieve diagnostic trouble codes (DTCs)
2
Check engine oil and coolant levels to ensure proper fluid conditions
3
Inspect the gas cap for damage or improper sealing
4
Examine the air filter for clogs or dirt that may affect engine performance
5
Test the battery and alternator output for proper voltage levels
6
Inspect spark plugs and ignition coils for wear or damage

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Oxygen sensor socket
•Torque wrench
•Multimeter

Parts Required

•Oxygen sensor (if applicable)
•Spark plugs
•Ignition coils (if applicable)
•Engine oil and filter (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to retrieve diagnostic trouble codes (DTCs)
2
Check engine oil and coolant levels to ensure proper fluid conditions
3
Inspect the gas cap for damage or improper sealing
4
Examine the air filter for clogs or dirt that may affect engine performance
5
Test the battery and alternator output for proper voltage levels
6
Inspect spark plugs and ignition coils for wear or damage

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a flat surface.
Disconnect the negative terminal of the battery for safety.

2. Retrieve Diagnostic Codes

Connect the OBD-II scanner to the vehicle's diagnostic port.
Turn the ignition to the "ON" position without starting the engine.
Retrieve and note any DTCs displayed by the scanner.

3. Address Issues Based on Diagnostic Codes

If codes indicate specific components (e.g., oxygen sensor, catalytic converter):
- Replace the faulty component following manufacturer specifications.
- For oxygen sensor replacement:
  1. Lift the vehicle and secure with jack stands.
  2. Disconnect the electrical connector.
  3. Use an oxygen sensor socket to unscrew the old sensor.
  4. Install the new sensor and reconnect the electrical plug.
If codes relate to misfires:
- Replace spark plugs and ignition coils as needed:
  1. Remove the engine cover (if applicable).
  2. Disconnect the ignition coil connectors.
  3. Unscrew and remove the ignition coils.
  4. Replace spark plugs if worn and reinstall coils.

4. Clear the Codes

After making repairs, use the OBD-II scanner to clear the error codes.
Turn the ignition off and then back on to ensure the check engine light is extinguished.

5. Reconnect Battery

Reconnect the negative battery terminal securely.