why does my Toyota Corolla E170 (2013-2019) make a grinding noise when turning

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

578 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn to diagnose and fix grinding noise when turning in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow engine to cool before opening any components.

Symptoms

•Grinding noise when turning the steering wheel
•Difficulty in steering or a feeling of stiffness
•Uneven tire wear
•Vibrations felt through the steering wheel
•Possible warning lights on the dashboard related to steering or traction control

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any leaks in the power steering system.
3
Visually inspect the CV joints and boots for damage or wear.
4
Examine the wheel bearings for play or noise.
5
Inspect the suspension components for any signs of wear or damage.
6
Test drive the vehicle to replicate the noise and determine conditions under which it occurs.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Jack stands
•Fluid pump
•Bearing puller
•Multimeter

Parts Required

•Power steering fluid
•CV axle (if needed)
•Wheel bearings (if needed)
•Suspension components (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any leaks in the power steering system.
3
Visually inspect the CV joints and boots for damage or wear.
4
Examine the wheel bearings for play or noise.
5
Inspect the suspension components for any signs of wear or damage.
6
Test drive the vehicle to replicate the noise and determine conditions under which it occurs.

Solution

1. Preparation

Gather tools: socket set, torque wrench, jack stands, and a multimeter.
Ensure the vehicle is parked on a level surface and the engine is turned off.
Disconnect the battery if working on electrical components.

2. Inspect and Replace Power Steering Fluid

Step 1: Locate the power steering reservoir.
Step 2: Check fluid level; if low, top up with the recommended fluid type (usually ATF or specific power steering fluid).
Step 3: If the fluid is dirty or has a burnt smell, drain and replace it.
Tools Required: Fluid pump, funnel.

3. Inspect and Replace CV Joints

Step 1: Raise the front end of the vehicle and secure it with jack stands.
Step 2: Remove the wheel to access the CV axle.
Step 3: Check the CV joint for any signs of wear, such as cracks in the boot or excessive play.
Step 4: If damaged, remove the CV axle using a socket set and replace with a new part.
Tools Required: Socket set, torque wrench.

4. Inspect and Replace Wheel Bearings

Step 1: With the wheel removed, grab the hub and check for play by moving it up and down.
Step 2: If play is detected, remove the hub assembly to access the wheel bearings.
Step 3: Replace the bearings if they are worn or noisy.
Tools Required: Bearing puller, socket set, torque wrench.

5. Inspect Suspension Components

Step 1: Look for any damaged bushings, struts, or control arms.
Step 2: Replace any worn or damaged components as necessary.
Tools Required: Socket set, suspension tools.