why does my Toyota Corolla E170 (2013-2019) transmission slip when I accelerate

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

525 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix transmission slippage in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow the engine to cool before removing any components to prevent burns.

Symptoms

•Engine RPM increases without corresponding increase in vehicle speed
•Delayed engagement when shifting from park to drive/reverse
•Unusual noises such as whining or grinding during acceleration
•Check engine light illuminated
•Harsh or erratic shifting
•Fluid leakage under the vehicle

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify potential transmission-related issues.
2
Check the transmission fluid level and condition; look for signs of contamination or burning.
3
Inspect the transmission fluid for proper color and smell; fresh fluid should be red and not burnt.
4
Examine the transmission filter for clogs or restrictions.
5
Inspect the transmission linkage and mounts for signs of wear or damage.
6
Test the throttle position sensor (TPS) and mass airflow sensor (MAF) for correct operation.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Transmission fluid pump
•Socket set
•Torque wrench
•Multimeter

Parts Required

•Toyota ATF WS transmission fluid
•Transmission filter
•Gasket for transmission pan
•Throttle position sensor (if replacement is necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify potential transmission-related issues.
2
Check the transmission fluid level and condition; look for signs of contamination or burning.
3
Inspect the transmission fluid for proper color and smell; fresh fluid should be red and not burnt.
4
Examine the transmission filter for clogs or restrictions.
5
Inspect the transmission linkage and mounts for signs of wear or damage.
6
Test the throttle position sensor (TPS) and mass airflow sensor (MAF) for correct operation.

Solution

1. Preparation

Gather tools and parts needed for repair.
Ensure the vehicle is on a flat surface and securely raise it using jack stands.
Disconnect the battery to prevent electrical shorts.

2. Check and Replace Transmission Fluid

Sub-steps:
1. Remove the transmission dipstick and check fluid level.
2. If low, add the recommended transmission fluid (Toyota ATF WS).
3. If fluid is dirty or burnt, proceed to drain and replace.
4. Drain the old transmission fluid through the drain plug.
5. Replace the transmission filter by removing the pan and installing a new filter.
6. Reinstall the pan with a new gasket and torque to the manufacturer’s specifications (typically 7-10 Nm).

3. Inspect and Repair Linkage

Sub-steps:
1. Visually inspect the transmission linkage for wear or disconnection.
2. Adjust or replace linkage components as necessary to ensure proper engagement.
3. Tighten any loose bolts and ensure all connections are secure.

4. Address Electrical Issues

Sub-steps:
1. Test the throttle position sensor (TPS) using a multimeter for correct voltage output.
2. Replace the TPS if readings are out of specification.
3. Check the mass airflow sensor (MAF) for proper function and clean or replace as needed.