why is my Toyota Corolla E170 (2013-2019) making a knocking noise

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

511 words

Problem Statement

Diagnose and fix knocking noise in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before handling components.

Symptoms

•Knocking noise when driving, especially during acceleration
•Noise may become more pronounced at higher speeds
•Possible vibrations felt through the steering wheel
•Decreased engine performance or responsiveness
•Check engine light may illuminate (if related to a component failure)

Diagnostic Steps

1
Inspect the engine for any loose components, such as heat shields or covers.
2
Check the engine oil level and condition; low or dirty oil can cause knocking.
3
Use an OBD-II scanner to check for any error codes that may indicate engine issues.
4
Perform a visual inspection of the suspension components for wear or damage.
5
Test drive the vehicle to replicate the noise and determine if it correlates with specific RPM or load conditions.
6
Listen carefully to the engine with a mechanic's stethoscope to isolate the source of the knocking noise.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Oil filter wrench
•Drain pan
•Funnel
•Jack and jack stands
•OBD-II scanner

Parts Required

•Engine oil (0W-20)
•Oil filter
•Any necessary suspension components (if damaged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the engine for any loose components, such as heat shields or covers.
2
Check the engine oil level and condition; low or dirty oil can cause knocking.
3
Use an OBD-II scanner to check for any error codes that may indicate engine issues.
4
Perform a visual inspection of the suspension components for wear or damage.
5
Test drive the vehicle to replicate the noise and determine if it correlates with specific RPM or load conditions.
6
Listen carefully to the engine with a mechanic's stethoscope to isolate the source of the knocking noise.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is cool.
Disconnect the battery to avoid any electrical issues during repair.

2. Inspect and Tighten Engine Components

Tools Required: Socket set, torque wrench
Check all visible engine mounts and fasteners; tighten any that are loose to specifications.
Inspect and re-tighten any loose heat shields or covers that could be rattling.

3. Change Engine Oil and Filter

Tools Required: Oil filter wrench, drain pan, funnel
Drain the existing engine oil using a drain pan; remove the oil drain plug.
Replace the oil filter using an oil filter wrench.
Refill the engine with the manufacturer-recommended oil type (typically 0W-20 for this model) and capacity.

4. Inspect Suspension Components

Tools Required: Jack and jack stands, socket set
Safely lift the vehicle using a jack and secure with jack stands.
Inspect suspension components (struts, control arms, bushings) for wear or damage.
Replace any damaged components as necessary.

5. Reassemble and Reconnect

Reinstall any removed engine covers and ensure all fasteners are tight.
Reconnect the battery and ensure all connections are secure.