my Toyota Tacoma N300 (2016-Present) remote start not working, what should I do

Toyota Tacoma N300 (2016-Present)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

474 words

Problem Statement

Learn how to diagnose and fix the remote start issue in your 2016-present Toyota Tacoma N300. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Electrical

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on the vehicle's electrical systems if necessary

Symptoms

•Remote start button does not respond
•Vehicle does not start when remote start is activated
•Check engine light illuminated
•Security indicator light flashing or illuminated
•No response from the key fob when attempting to start

Diagnostic Steps

1
Check the battery voltage of the key fob using a multimeter
2
Inspect the key fob for physical damage or worn buttons
3
Scan the vehicle’s onboard diagnostics (OBD-II) for any stored error codes
4
Verify that the vehicle is in the proper condition for remote start (e.g., doors closed, hood closed, transmission in park)
5
Check the vehicle's battery voltage and overall electrical system health
6
Inspect the remote start system's wiring and connections for damage or disconnection

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Basic hand tools (screwdrivers, socket set)

Parts Required

•Key fob battery (CR2032 or as specified)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the battery voltage of the key fob using a multimeter
2
Inspect the key fob for physical damage or worn buttons
3
Scan the vehicle’s onboard diagnostics (OBD-II) for any stored error codes
4
Verify that the vehicle is in the proper condition for remote start (e.g., doors closed, hood closed, transmission in park)
5
Check the vehicle's battery voltage and overall electrical system health
6
Inspect the remote start system's wiring and connections for damage or disconnection

Solution

1. Preparation

Gather tools: OBD-II scanner, multimeter, basic hand tools (screwdrivers, socket set).
Ensure the vehicle is parked in a safe location and that the engine is off.

2. Replace Key Fob Battery

Sub-steps:
1. Open the key fob using a small flathead screwdriver.
2. Remove the old battery and replace it with a new battery of the same type (typically CR2032).
3. Reassemble the key fob and test the remote start function.

3. Check Remote Start Conditions

Sub-steps:
1. Ensure all doors, the trunk, and the hood are securely closed.
2. Confirm that the vehicle is in 'Park' mode.
3. Attempt to use the remote start feature again.

4. Inspect and Reset the Remote Start System

Sub-steps:
1. Locate the remote start system module (typically installed under the dashboard).
2. Inspect for any visible damage or loose connections.
3. If applicable, disconnect the module for 5 minutes to reset it and reconnect.

5. Clear Error Codes

Sub-steps:
1. Connect the OBD-II scanner to the vehicle’s OBD port.
2. Scan for and note any error codes related to the remote start system.
3. Clear the error codes and attempt to use remote start again.