how can I fix the AC that makes a loud noise in my Volkswagen Golf MK7.5 (2020-Present)?

Volkswagen Golf MK7.5 (2020-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

554 words

Problem Statement

Learn how to diagnose and fix loud AC noise in Volkswagen Golf MK7.5. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

HVAC

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Allow the engine to cool before inspecting the AC system.

Symptoms

•Loud noise when AC is turned on
•Decreased cooling efficiency
•Unusual vibrations felt through the dashboard
•Intermittent operation of the AC system
•Possible refrigerant leaks (evident from oily residue)

Diagnostic Steps

1
Inspect the AC compressor for signs of wear or damage.
2
Check the AC condenser for obstructions or debris.
3
Examine the blower motor for unusual noises or vibrations.
4
Inspect the AC belt for fraying or excessive wear.
5
Use an OBD-II scanner to check for any related fault codes.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Screwdriver set
•Tensioner tool
•Compressed air

Parts Required

•AC compressor (if damaged)
•AC belt (if worn)
•Cabin air filter (if dirty)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Solution

1. Preparation

Gather all necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is turned off.
Disconnect the negative battery terminal to prevent electrical shock.

2. Inspect the AC Compressor

Tools Required: Socket set, torque wrench
Remove the AC compressor belt:
- Release tension from the serpentine belt using a tensioner tool.
- Carefully slide the belt off the compressor pulley.
Inspect the compressor:
- Check for visible damage or unusual wear on the compressor.
- Rotate the pulley by hand to check for smooth operation. If it feels gritty or binds, consider replacing the compressor.

3. Check the AC Condenser

Tools Required: None
Visually inspect the condenser for debris (leaves, dirt):
- Use compressed air to blow out any obstructions.
If the condenser is damaged, it will need to be replaced.

4. Examine the Blower Motor

Tools Required: Screwdriver set
Remove the blower motor assembly:
- Access the blower motor by removing the glove box as needed.
- Disconnect the electrical connector and unscrew the blower motor from its housing.
Inspect the blower motor for debris or damage:
- Clean any obstructions and test for proper operation by applying direct power to the motor.

5. Inspect the AC Belt

Tools Required: None
Check the AC belt for signs of wear or fraying:
- If the belt shows signs of cracking or excessive wear, replace it with a new one.
Reinstall the belt and ensure proper tension.

6. Reassemble and Recharge AC System

Reconnect all components and ensure everything is securely fastened.
Reconnect the negative battery terminal.
Recharge the AC system with the appropriate refrigerant according to the manufacturer's specifications.