Volkswagen Golf MK7.5 (2020-Present) steering column making clicking noise how to fix

Volkswagen Golf MK7.5 (2020-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

573 words

Problem Statement

Learn how to diagnose and fix the clicking noise in the steering column of your Volkswagen Golf MK7.5. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Allow the vehicle to cool before working on any components that may have been heated during operation.

Symptoms

•Clicking noise when turning the steering wheel
•Difficulty in steering movement
•Potential play or looseness in the steering wheel
•Unusual resistance felt while steering
•Warning lights illuminated on the dashboard (e.g., EPS light)

Diagnostic Steps

1
Inspect the steering column for visible damage or misalignment.
2
Check the steering fluid level and condition; top up or replace if necessary.
3
Scan the vehicle's computer using an OBD-II scanner for any fault codes related to steering or EPS (Electric Power Steering).
4
Verify the tightness of all fasteners and bolts on the steering assembly.
5
Test the steering linkage for wear or damage by visually inspecting the tie rods and ball joints.
6
Check for any debris or obstructions in the steering column area.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Screwdriver set
•Grease

Parts Required

•Steering column bearings (if worn)
•Steering column bushings (if damaged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the steering column for visible damage or misalignment.
2
Check the steering fluid level and condition; top up or replace if necessary.
3
Scan the vehicle's computer using an OBD-II scanner for any fault codes related to steering or EPS (Electric Power Steering).
4
Verify the tightness of all fasteners and bolts on the steering assembly.
5
Test the steering linkage for wear or damage by visually inspecting the tie rods and ball joints.
6
Check for any debris or obstructions in the steering column area.

Solution

1. Preparation

Gather all necessary tools and parts.
Ensure the vehicle is parked on a flat surface with the ignition off.
Disconnect the battery to ensure safety while working on electrical components.

2. Remove the Steering Wheel

Sub-steps:
- Using a socket set, carefully remove the airbag from the steering wheel. Disconnect the airbag connector.
- Unscrew the center nut that holds the steering wheel in place using a torque wrench.
- Mark the position of the steering wheel on the shaft to ensure correct alignment upon reinstallation.
- Gently pull the steering wheel off the shaft.

3. Inspect the Steering Column Assembly

Sub-steps:
- Remove the plastic covers from the steering column by unscrewing the retaining screws.
- Check for any loose or damaged components within the steering column.
- Inspect the steering column bearings and bushings for wear or damage; replace if necessary.

4. Repair or Replace Damaged Components

Sub-steps:
- If any components are worn, order replacements and install them according to the manufacturer's specifications.
- Lubricate any moving parts within the steering column with appropriate grease to eliminate the clicking noise.

5. Reassemble the Steering Column

Sub-steps:
- Reinstall the steering column covers, securing them with screws.
- Align the steering wheel with the mark made earlier and reinstall it onto the steering shaft.
- Torque the center nut to the manufacturer's specifications (typically around 35 Nm).
- Reconnect the airbag and ensure it's properly seated.

6. Final Checks

Reconnect the battery and start the vehicle.
Test the steering for smooth operation and ensure no clicking noise is present.