why does my Volkswagen Golf MK7 (2015-2019) AC not blow cold air anymore

Volkswagen Golf MK8.5 (2024-Present)

Error Codes

1-3 hours

Time

medium

Difficulty

medium

Severity

3 min read

476 words

Problem Statement

Learn how to diagnose and fix AC not blowing cold air in Volkswagen Golf MK7 (2015-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

HVAC

Estimated Time

1-3 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Handle refrigerants with care and follow proper disposal procedures.

Symptoms

•AC compressor not engaging
•Warm air blowing from vents
•AC system making unusual noises (e.g., clicking or buzzing)
•Increased humidity inside the vehicle
•AC warning light illuminated on the dashboard

Diagnostic Steps

1
Inspect the AC system fuse for any blown fuses.
2
Use an OBD-II scanner to check for any error codes related to the AC system.
3
Verify the refrigerant level using a refrigerant gauge.
4
Examine the AC compressor for signs of damage or leaks.
5
Check the cabin air filter for clogs or blockages.
6
Inspect the AC pressure switch operation.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Refrigerant gauge
•Screwdrivers
•Pliers
•AC recharge kit

Parts Required

•R-134a refrigerant
•Cabin air filter
•AC fuse (if blown)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the AC system fuse for any blown fuses.
2
Use an OBD-II scanner to check for any error codes related to the AC system.
3
Verify the refrigerant level using a refrigerant gauge.
4
Examine the AC compressor for signs of damage or leaks.
5
Check the cabin air filter for clogs or blockages.
6
Inspect the AC pressure switch operation.

Solution

1. Preparation

Gather tools and parts needed for the repair.
Disconnect the negative battery terminal to avoid any electrical issues.

2. Detect and Replace the Fuse

Locate the AC fuse in the fuse box (refer to the owner's manual for location).
Check if the fuse is blown and replace it if necessary (use a fuse of the same amperage).

3. Recharge Refrigerant

Connect the refrigerant gauge to the low-pressure service port.
If the refrigerant level is low, prepare to recharge the system:
- Use R-134a refrigerant.
- Follow instructions on the refrigerant can for proper filling.
- Monitor the low-pressure gauge while recharging to avoid overfilling.

4. Inspect and Replace the Cabin Air Filter

Remove the cabin air filter cover (usually located behind the glove box).
Take out the old cabin air filter and inspect for dirt and blockages.
Replace with a new cabin air filter, ensuring it is oriented correctly.

5. Test the AC Compressor

Reconnect the negative battery terminal.
Start the engine and turn on the AC to the maximum setting.
Observe the AC compressor; if it does not engage, inspect the wiring and the AC pressure switch for faults.