why does my Volkswagen Tiguan Second Generation (2018-present) have a clicking noise when turning?

Volkswagen Tiguan 2nd Gen (2018-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

573 words

Problem Statement

Learn how to diagnose and fix clicking noise when turning in Volkswagen Tiguan. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always ensure the vehicle is securely supported on jack stands before working underneath it.
•Disconnect the battery before working on electrical systems to prevent short circuits.

Symptoms

•Clicking or popping noise when turning the steering wheel
•Noise may increase with sharper turns
•Vibration felt through the steering wheel
•Possible loss of steering responsiveness
•Unusual wear on tires (outer edge)

Diagnostic Steps

1
Inspect the front axle and CV joints for any visible damage or wear.
2
Check the wheel bearings for play or excessive noise when rotating the wheel.
3
Examine the suspension components, including control arms and bushings, for wear.
4
Test drive the vehicle to replicate the noise while observing steering and suspension performance.
5
Use a stethoscope to pinpoint the source of the noise if necessary.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Lug wrench
•Pliers
•Flashlight
•Torque wrench
•Wrench set
•Pry bar

Parts Required

•CV joint or axle assembly (if damaged)
•Wheel bearing (if faulty)
•Suspension components (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the front axle and CV joints for any visible damage or wear.
2
Check the wheel bearings for play or excessive noise when rotating the wheel.
3
Examine the suspension components, including control arms and bushings, for wear.
4
Test drive the vehicle to replicate the noise while observing steering and suspension performance.
5
Use a stethoscope to pinpoint the source of the noise if necessary.

Solution

1. Preparation

Gather tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the battery to ensure safety while working on electrical systems.

2. Inspect and Remove Front Wheel

Tools Required: Jack, jack stands, lug wrench
Sub-steps:
1. Loosen the lug nuts of the front wheels while the vehicle is on the ground.
2. Raise the vehicle using a jack and secure it with jack stands.
3. Remove the front wheel to access the suspension and drivetrain components.

3. Examine CV Joints

Tools Required: Pliers, flashlight
Sub-steps:
1. Inspect the outer CV joint for torn boots or grease leakage.
2. Check for play in the joint by moving it up and down.
3. If damaged, replace the CV joint or axle assembly as needed.

4. Inspect Wheel Bearings

Tools Required: Torque wrench, wheel bearing grease
Sub-steps:
1. Rotate the wheel by hand and listen for grinding noises.
2. Check for any play in the wheel bearing by wiggling the wheel side to side.
3. If the bearing is faulty, remove the hub assembly and replace the wheel bearing.

5. Examine Suspension Components

Tools Required: Wrench set, pry bar
Sub-steps:
1. Inspect control arms and bushings for any cracks or deterioration.
2. Use a pry bar to check for excessive movement in the bushings.
3. Replace any worn or damaged suspension components as necessary.

6. Reassemble and Test

Tools Required: Torque wrench
Sub-steps:
1. Reinstall the wheel and hand-tighten the lug nuts.
2. Lower the vehicle and torque the lug nuts to the manufacturer’s specifications.
3. Test drive the vehicle to ensure the noise has been resolved.